انتبه إلى 4 نقاط رئيسية عند استخدام مركز المعالجة الأفقي
يشير مركز المعالجة الأفقي إلى مركز المعالجة حيث يتم ترتيب الطاولة والمغزل بالتوازي. عادة ما يحتوي مركز المعالجة الأفقي على ثلاثة محاور حركة خطية بالإضافة إلى محور دوار طاولة واحد. يمكن لمركز المعالجة الأفقي تحديد أدوات مختلفة تلقائيا وفقا للبرنامج بعد تثبيت قطعة العمل في وقت واحد ، وتغيير سرعة دوران المغزل تلقائيا ، وإكمال معالجة عمليات متعددة على أسطح متعددة بالتسلسل. مركز المعالجة هو الأنسب لتصنيع الخزانة. أجزاء الفصل. بعد ذلك ، سأقدم النقاط الأربع الرئيسية للاهتمام في استخدام مراكز المعالجة الأفقية.
تركيب بيئة مركز المعالجة الأفقية
مركز المعالجة الأفقيةs should be installed away from sources, away from direct sunlight, without heat radiation and without moisture. If there is a source near the place where the مركز المعالجة الأفقية is installed, a shock-proof groove should be placed around the مركز المعالجة الأفقية. If the anti-shock is not provided, it will directly affect the processing accuracy and stability of the مركز المعالجة الأفقية. Over time, it will affect the poor contact of the electronic components and cause failure, which will affect the reliability of the مركز المعالجة الأفقية.
رقابة صارمة على الجهد والتيار
مركز المعالجة الأفقيةs are generally installed in the processing workshop, and the processing equipment has a large number of mechanical equipment, which inevitably leads to large fluctuations in the power grid. Therefore, the position of the مركز المعالجة الأفقية must be strictly controlled to control the voltage and current of the power supply. It is necessary to control the voltage and current of the power supply within the allowable range of the مركز المعالجة الأفقية. It is necessary to keep the voltage and current of the power supply stable, otherwise it will directly affect the lying. The normal operation of the machining center.
Temperature and humidity will directly affect the مركز المعالجة الأفقية
مركز المعالجة الأفقيةs generally need to be in an environment below 30 degrees Celsius to work properly. Generally, exhaust fans and air coolers are installed in the distribution box of the مركز المعالجة الأفقية to ensure that the electronic components and the central processing are working under constant temperature. . If the temperature and humidity are too high, the component life of the control system will be reduced, resulting in an increase in the failure of the مركز المعالجة الأفقية. When the humidity is increased, the dust will increase on the integrated circuit board and directly cause a malfunction of short contact and short circuit.
إعداد معلمة مصنع الماكينة
When using the مركز المعالجة الأفقية, the customer can't change the factory parameter setting of the machine at will, because these factory parameter settings are directly related to the dynamic characteristics of each part of the مركز المعالجة الأفقية. Only the gap compensation parameter value can be set according to the actual situation.
تركيب بيئة مركز المعالجة الأفقية
مركز المعالجة الأفقيةs should be installed away from sources, away from direct sunlight, without heat radiation and without moisture. If there is a source near the place where the مركز المعالجة الأفقية is installed, a shock-proof groove should be placed around the مركز المعالجة الأفقية. If the anti-shock is not provided, it will directly affect the processing accuracy and stability of the مركز المعالجة الأفقية. Over time, it will affect the poor contact of the electronic components and cause failure, which will affect the reliability of the مركز المعالجة الأفقية.
رقابة صارمة على الجهد والتيار
مركز المعالجة الأفقيةs are generally installed in the processing workshop, and the processing equipment has a large number of mechanical equipment, which inevitably leads to large fluctuations in the power grid. Therefore, the position of the مركز المعالجة الأفقية must be strictly controlled to control the voltage and current of the power supply. It is necessary to control the voltage and current of the power supply within the allowable range of the مركز المعالجة الأفقية. It is necessary to keep the voltage and current of the power supply stable, otherwise it will directly affect the lying. The normal operation of the machining center.
Temperature and humidity will directly affect the مركز المعالجة الأفقية
مركز المعالجة الأفقيةs generally need to be in an environment below 30 degrees Celsius to work properly. Generally, exhaust fans and air coolers are installed in the distribution box of the مركز المعالجة الأفقية to ensure that the electronic components and the central processing are working under constant temperature. . If the temperature and humidity are too high, the component life of the control system will be reduced, resulting in an increase in the failure of the مركز المعالجة الأفقية. When the humidity is increased, the dust will increase on the integrated circuit board and directly cause a malfunction of short contact and short circuit.
إعداد معلمة مصنع الماكينة
When using the مركز المعالجة الأفقية, the customer can't change the factory parameter setting of the machine at will, because these factory parameter settings are directly related to the dynamic characteristics of each part of the مركز المعالجة الأفقية. Only the gap compensation parameter value can be set according to the actual situation.